VLSI TECHNICAL INTERVIEW QUESTIONS & ANSWERS PART -2


Bonus Tips 

1)In the process of the they try to ask you about piratical work you had done so my  suggestion is do basic work on the on the project that you mentioned in your resume

2)Have a grip on the vlsi design flow and you should each and every thing right from the beginning.

3)test your self before going to the interview so that you can know about your self.

4) if you are backend developer (physical design) then be strong in layouts and designing of them 



INTERVIEW QUESTION:

 22 ) What is glitch? What causes it (explain with waveform)? How to overcome it?

The following figure shows a synchronous alternative to the gated clock using a data path. The flip-flop is clocked at every clock cycle and the data path is controlled by an enable. When the enable is Low, the multiplexer feeds the output of the register back on itself. When the enable is High, new data is fed to the flip-flop and the register changes its state


23) What is difference between latch and flipflop?

The main difference between latch and FF is that latches are level sensitive while FF are edge sensitive. They both require the use of clock signal and are used in sequential logic. For a latch, the output tracks the input when the clock signal is high, so as long as the clock is logic 1, the output can change if the input also changes. FF on the other hand, will store the input only when there is a rising/falling edge of the clock.


24)Guys this is the basic question asked most frequently. Design all the basic gates(NOT,AND,OR,NAND,NOR,XOR,XNOR) using 2:1 Multiplexer?

Using 2:1 Mux, (2 inputs, 1 output and a select line)

(a) NOT

Give the input at the select line and connect I0 to 1 & I1 to 0. So if A is 1, we will get I1 that is 0 at the O/P.

(b) AND

Give input A at the select line and 0 to I0 and B to I1. O/p is A & B

(c) OR

Give input A at the select line and 1 to I1 and B to I0. O/p will be A | B

(d) NAND

AND + NOT implementations together

(e) NOR

OR + NOT implementations together

(f) XOR

A at the select line B at I0 and ~B at I1. ~B can be obtained from (a) 

(g) XNOR 

A at the select line B at I1 and ~B at I0

25)what is difference between RAM and FIFO?

FIFO does not have address lines

Ram is used for storage purpose where as fifo is used for synchronization purpose i.e.

when two peripherals are working in different clock domains then we will go for fifo.

26) What are multi-cycle paths?

Multi-cycle paths are paths between registers that take more than one clock cycle to

become stable.

For ex. Analyzing the design shown in fig below shows that the output SIN/COS requires

4 clock-cycles after the input ANGLE is latched in. This means that the combinatorial

block (the Unrolled Cordic) can take up to 4 clock periods (25MHz) to propagate its

result. Place and Route tools are capable of fixing multi-cycle paths problem.

27)what is false path?how it determine in ckt? what the effect of false path in ckt?

By timing all the paths in the circuit the timing analyzer can determine all the critical paths in the circuit. However, the circuit may have false paths, which are the paths in the circuit which are never exercised during normal circuit operation for any set of inputs. An example of a false path is shown in figure below. The path going from the input A of the first MUX through the combinational logic out through the B input of the second MUX is a false path. This path can never be activated since if the A input of the first MUX is activated, then Sel line will also select the A input of the second MUX. STA (Static Timing Analysis) tools are able to identify simple false paths; however they are not able to identify all the false paths and sometimes report false paths as critical paths. Removal of false paths makes circuit testable and its timing performance predictable (sometimes faster)

28) what is false path?how it determine in ckt? what the effect of false path in ckt?

By timing all the paths in the circuit the timing analyzer can determine all the critical

paths in the circuit. However, the circuit may have false paths, which are the paths in the

circuit which are never exercised during normal circuit operation for any set of inputs.

An example of a false path is shown in figure below. The path going from the input A of

the first MUX through the combinational logic out through the B input of the second

MUS is a false path. This path can never be activated since if the A input of the first

MUX is activated, then Sel line will also select the A input of the second MUX.

STA (Static Timing Analysis) tools are able to identify simple false paths; however they

are not able to identify all the false paths and sometimes report false paths as critical

paths. Removal of false paths makes circuit testable and its timing performance

predictable (sometimes faster) order to succeed. In other words, big enough that manually drawing lots of little blue, red

and green lines is too much for a human to reasonably do. I think that, likewise, SoC is

that level of integration onto a chip that demands more expertise beyond traditional skills

of electronics. In other words, pulling off a SoC demands Hardware, Software, and

Systems Engineering talent. So, trivially, SoCs aggressively combine HW/SWon a single

chip. Maybe more pragmatically, SoC just means that ASIC and Software folks are

learning a little bit more about each other's techniques and tools than they did before.

Two other interpretations of SoC are 1) a chip that integrates various IP (Intellectual

Property) blocks on it and is thus highly centered with issues like Reuse, and 2) a chip

integrating multiple classes of electronic circuitry such as Digital CMOS, mixed-signal

digital and analog (e.g. sensors, modulators, A/Ds), DRAM memory, high voltage power,

etc. ASIC stands

29 )What is "Scan" ?

§Scan Insertion and ATPG helps test ASICs (e.g. chips) during manufacture. If you know

what JTAG boundary scan is, then Scan is the same idea except that it is done inside the

chip instead of on the entire board. Scan tests for defects in the chip's circuitry after it is

manufactured (e.g. Scan does not help you test whether your Design functions as

intended). ASIC designers usually implement the scan themselves and occurs just after

synthesis. ATPG (Automated Test Pattern Generation) refers to the creation of "Test

Vectors" that the Scan circuitry enables to be introduced into the chip. Here's a brief

summary:

· Scan Insertion is done by a tool and results in all (or most) of your design's flip-flops to

be replaced by special "Scan Flip-flops". Scan flops have additional inputs/outputs that

allow them to be configured into a "chain" (e.g. a big shift register) when the chip is put

into a test mode.

· The Scan flip-flops are connected up into a chain (perhaps multiple chains)

· The ATPG tool, which knows about the scan chain you've created, generates a series of

test vectors.

· The ATPG test vectors include both "Stimulus" and "Expected" bit patterns. These bit

vectors are shifted into the chip on the scan chains, and the chips reaction to the stimulus

is shifted back out again.

· The ATE (Automated Test Equipment) at the chip factory can put the chip into the scan

test mode, and apply the test vectors. If any vectors do not match, then the chip is

defective and it is thrown away.

· Scan/ATPG tools will strive to maximize the "coverage" of the ATPG vectors. In other

words, given some measure of the total number of nodes in the chip that could be faulty

(shorted, grounded, "stuck at 1", "stuck at 0"), what percentage of them can be detected

with the ATPG vectors? Scan is a good technology and can achive high coverage in the

90% range.

Scan testing does not solve all test problems. Scan testing typically does not test

memories (no flip-flops!), needs a gate-level netlist to work with, and can take a long

time to run on the ATE.

· FPGA designers may be unfamiliar with scan since FPGA testing has already been done

by the FPGA manufacturer. ASIC designers do not have this luxury and must handle all

the manufacturing test details themselves.

30) Difference between task and function?( IMPORTANT )

Function:

A function is unable to enable a task however functions can enable other functions.

A function will carry out its required duty in zero simulation time. ( The program time

will not be incremented during the function routine)

Within a function, no event, delay or timing control statements are permitted

In the invocation of a function their must be at least one argument to be passed.

Functions will only return a single value and can not use either output or inout

statements.

Tasks:

Tasks are capable of enabling a function as well as enabling other versions of a Task

Tasks also run with a zero simulation however they can if required be executed in a non

zero simulation time.

Tasks are allowed to contain any of these statements.

A task is allowed to use zero or more arguments which are of type output, input or inout.

A Task is unable to return a value but has the facility to pass multiple values via the

output and inout statements .


Part-1 if not visited for the better content

https://vlsitechinterview.blogspot.com/2020/08/vlsi-technical-interview-questions.html


Comments

Popular posts from this blog

VLSI TECHNICAL INTERVIEW QUESTIONS & ANSWERS PART-1