VLSI TECHNICAL INTERVIEW QUESTIONS & ANSWERS PART-1

 Interview preparation:

1)BE STRONG IN THE BASICS

2)IF DON'T KNOW LEAVE THE QUESTION DON'T TRY TO PRETEND THAT YOU KNOW EVERY THING.( BIGGEST MISTAKE EVERY ONE DO'S)

3) TELL WHAT YOU CAN DO TO THEM IF YOU ARE REQUITED

The purpose of interview preparation through specific question is to relieve you from having to

learn the whole subject as if you would learn it at school. You obviously do not need to relearn

the subject as you have already learned the subject. There are two things that you need to do.

1) Make sure you have a sound understanding of the fundamental concepts.

2) Be confident even if you are wrong .

Tips:

If you think you need to address some of the fundamental, best way is to take up some of the

popular text-books and thoroughly read through them. 

There is a set of questions and topics that are much more likely to be discussed during the

interview process. Although in the school you systematically learn through many aspects of

the digital VLSI design, in reality you do not use all the theoretical knowledge. In industry there

are certain topics and certain issues, which are faced on a very regular basis while working on

practical designs. These specific issues are of much more practical importance than anything

else when it comes to doing the actual design of the ASIC chips.

For example when you synthesize RTL, coding styles is very important as what logic you

infer, will depends upon that. Your clock and reset distribution schemes are paramount for

synchronous circuit design. Most of the textbooks do not comprehensively address the topic of

timing fixes and improvements.

 

If you ask enough people who have taken interviews, you will soon figure out the pattern that repeats.

If you can provide special attention to this set of special questions and topics, you will have an

edge compared to other and it will benefit you immensely by improving your confidence and

increasing your chances of success at interview.

Following is a list of answers to a subset of the very important questions that you need to

master in the field of digital VLSI design.


1) What is latch up?

Latch-up pertains to a failure mechanism wherein a parasitic thyristor (such as a parasitic

silicon controlled rectifier, or SCR) is inadvertently created within a circuit, causing a

high amount of current to continuously flow through it once it is accidentally triggered or

turned on. Depending on the circuits involved, the amount of current flow produced by

this mechanism can be large enough to result in permanent destruction of the device due

to electrical overstress (EOS)

2)Why is NAND gate preferred over NOR gate for fabrication?

NAND is a better gate for design than NOR because at the transistor level the mobility of

electrons is normally three times that of holes compared to NOR and thus the NAND is a

faster gate.

Additionally, the gate-leakage in NAND structures is much lower. If you consider t_phl

and t_plh delays you will find that it is more symmetric in case of NAND ( the delay

profile), but for NOR, one delay is much higher than the other(obviously t_plh is higher

since the higher resistance p mos's are in series connection which again increases the

resistance).

3)What is Noise Margin? Explain the procedure to determine Noise Margin

The minimum amount of noise that can be allowed on the input stage for which the

output will not be effected.

4)Explain sizing of the inverter?

In order to drive the desired load capacitance we have to increase the size (width) of the

inverters to get an optimized performance.

5) How do you size NMOS and PMOS transistors to increase the threshold voltage?

generally in industrial standard we double the size of PMOS compared to NMOS because PMOS takes more time to charge the output when compared to NMOS

6) What is Noise Margin? Explain the procedure to determine Noise Margin?

The minimum amount of noise that can be allowed on the input stage for which the output will not be effected.

7) What happens to delay if you increase load capacitance?

delay increases.

8)What happens to delay if we include a resistance at the output of a CMOS circuit?

Increases. (RC delay)

9)What are the limitations in increasing the power supply to reduce delay?

The delay can be reduced by increasing the power supply but if we do so the heating .effect comes because of excessive power, to compensate this we have to increase the die size which is not practical.


10)How does Resistance of the metal lines vary with increasing thickness and increasing

length?

R = ( *l) / A.

11)For CMOS logic, give the various techniques you know to minimize power

consumption?

Power dissipation=CV2f ,from this minimize the load capacitance, dc voltage and the

operating frequency.

12) What is Charge Sharing? Explain the Charge Sharing problem while sampling data

from a Bus?

In the serially connected NMOS logic the input capacitance of each gate shares the

charge with the load capacitance by which the logical levels drastically mismatched than

that of the desired once. To eliminate this load capacitance must be very high compared

to the input capacitance of the gates (approximately 10 times).

13)Why do we gradually increase the size of inverters in buffer design? Why not give the

output of a circuit to one large inverter?

Because it can not drive the output load straight away, so we gradually increase the size

to get an optimized performance.

14)What is Latch Up? Explain Latch Up with cross section of a CMOS Inverter. How do

you avoid Latch Up?

Latch-up is a condition in which the parasitic components give rise to the Establishment

of low resistance conducting path between VDD and VSS with Disastrous results.

15) Give the expression for CMOS switching power dissipation?

CV2

16) What is Body Effect?

In general multiple MOS devices are made on a common substrate. As a result, the

substrate voltage of all devices is normally equal. However while connecting the devices

serially this may result in an increase in source-to-substrate voltage as we proceed

vertically along the series chain (Vsb1=0, Vsb2 0).Which results Vth2>Vth1.

17) Why is the substrate in NMOS connected to Ground and in PMOS to VDD?

we try to reverse bias not the channel and the substrate but we try to maintain the

drain,source junctions reverse biased with respect to the substrate so that we dont loose

our current into the substrate.


18) .why code should be synthesized in the vlsi design?

This is the stage of building the Logical circuit using the standard cell libraries designed already. In the front end RTL we get on the 0 and 1 only but we need the logic behind it so synthesis is must and should.  this is also used to reduce the circuit area. 

19)All of us know how an inverter works. What happens when the PMOS and NMOS are

interchanged with one another in an inverter?

I have seen similar Qs in some of the discussions. If the source & drain also connected

properly...it acts as a buffer. But suppose input is logic 1 O/P will be degraded 1.Similarly degraded 0;

20)A good question on Layouts. Give 5 important Design techniques you would follow

when doing a Layout for Digital Circuits?

a)In digital design, decide the height of standard cells you want to layout.It depends upon

how big your transistors will be.Have reasonable width for VDD and GND metal

paths.Maintaining uniform Height for all the cell is very important since this will help

you use place route tool easily and also incase you want to do manual connection of all

the blocks it saves on lot of area.

b)Use one metal in one direction only, This does not apply for metal 1. Say you are using

metal 2 to do horizontal connections, then use metal 3 for vertical connections, metal4 for

horizontal, metal 5 vertical etc...

c)Place as many substrate contact as possible in the empty spaces of the layout.

d)Do not use poly over long distances as it has huge resistances unless you have no other

choice.

e)Use fingered transistors as and when you feel necessary.

f)Try maintaining symmetry in your design. Try to get the design in BIT Sliced manner.



I have a question for you if you know comment below:
21 ) What is metastability? When/why it will occur?Different ways to avoid this?

NOTE:
support & share to your friends and i will more question I will give hope this is useful i am design engineer these are basics asked in my interview i will share more for i you guys are supporting me 

THIS IS PART-2 LINK:

Thank you.

Comments

Popular posts from this blog

VLSI TECHNICAL INTERVIEW QUESTIONS & ANSWERS PART -2